Puppy Linux Discussion Forum

When the kernel is compiled with the EFI boot stub like the one packaged in Void, UEFI firmware can load the kernel directly as an EFI executable, eliminating the need for a bootloader.

In the following, we set up a simple Void system on a drive, with an encrypted root partition and an unencrypted EFI system partition. We will refer to the drive as /dev/sd<X>. I originally wrote this article for the Void Linux handbook, but it seems like they have long-term plans to turn their installation tutorials into a structured reference.
Provisioning

On the drive, create a GPT partition table with the following partitions:
No. Size Type
1 512MiB EFI System
2 rest of the drive Linux filesystem

Create a FAT 32 filesystem on the EFI System Partition, optionally giving it a label.

Code: Select all

# mkfs.fat -F 32 -n efi /dev/sd<X>1

Initialize the LUKS device.

Code: Select all

# cryptsetup luksFormat /dev/sd<X>2 --type luks2 --label luks

Open the LUKS device.

Code: Select all

# cryptsetup open --type luks /dev/sd<X>2 root

Create the desired file system.

Code: Select all

# mkfs.ext4 -L root /dev/mapper/root

Installation

With the LUKS device still open, mount the root filesystem, the EFI system partition and the necessary directories to /mnt.

Code: Select all

# mount /dev/mapper/root /mnt
# mkdir /mnt/boot
# mount /dev/sd<X>1 /mnt/boot
# for dir in dev proc sys run; do
> mkdir /mnt/$dir
> mount --rbind --make-rslave /$dir /mnt/$dir
> done

Install the Void Linux base system, cryptsetup and efibootmgr.

Code: Select all

# xbps-install -S -R https://alpha.de.repo.voidlinux.org/current -r /mnt base-system cryptsetup efibootmgr

Change the filesystem root to enter the new system.

Code: Select all

# chroot /mnt

Set the filesystem permissions, root password and hostname.

Code: Select all

# chown root:root /
# chmod 755 /
# passwd root
# echo void > /etc/hostname

Void Linux uses dracut to manage early userspace. Configure it to open and mount the LUKS device and mount the EFI variables and system partition. To this end, edit /etc/crypttab.

# <name> <device> <password> <options>
root /dev/disk/by-uuid/<UUID> none

The UUID of /dev/sd<X>2 can be determined with lsblk -f. We'd like to write /dev/disk/by-label/luks instead, but it seems udev doesn't support LUKS labels yet. The password field is a path to a file containing the password or none to prompt during boot.

Now, edit /etc/fstab.

Code: Select all

# <file system>	        <dir> <type>  <options>             <dump>  <pass>
tmpfs                   /tmp  tmpfs   defaults,nosuid,nodev 0       0
efivarfs  /sys/firmware/efi/efivars  efivarfs  defaults     0       0
/dev/disk/by-label/root /     ext4    defaults              0       1
/dev/disk/by-label/efi  /boot vfat    defaults              0       2

Create /etc/dracut.conf.d/30.conf to configure dracut.

Code: Select all

hostonly="yes"
use_fstab="yes"
install_items+=" /etc/crypttab "
add_drivers+=" vfat nls_cp437 nls_iso8859_1 "

Create a symbolic link from /etc/fstab.sys to /etc/fstab to indicate that dracut should mount all the file systems listed. Then, to omit mounting them again in runit stage 1, disable the corresponding core service.

Code: Select all

# mv /etc/runit/core-services/03-filesystems.sh{,.bak}

Edit /etc/xbps.d/xbps.conf to prevent the service from being added back by an update to runit-void.

Code: Select all

noextract=/etc/runit/core-services/03-filesystems.sh

We are choosing dracut to mount our filesystems because otherwise the filesystems core service will try to open the encrypted drive a second time. Another option would be to stop dracut from mounting anything at all.

Edit the configuration for efibootmgr's kernel hook in /etc/default/efiboomgr-kernel-hook for it to add boot entries. Kernel command-line parameters may be added with OPTIONS.

Code: Select all

MODIFY_EFI_ENTRIES="1"
DISK="/dev/sd<X>"
PART="1"

Invoke dracut and efibootmgr by reconfiguring the kernel. You can determine the installed kernel version by listing the dependencies of the linux meta-package using xbps-query.

Code: Select all

# xbps-reconfigure -f linux<major>.<minor>

As needed, modify the boot order using efibootmgr. To determine the current boot order and entries, invoke it without any arguments. To set the bootorder, use --bootorder XXXX,XXXX,....

Exit the chroot, unmount the filesystems and reboot.

Code: Select all

# exit
# umount -R /mnt
# reboot[/quote]

Original Blog post -> https://mth.st/blog/void-efistub/