Setup an Apache2 Web Server with Bionic

[rockedge]

These are the rough steps of getting an Apache2 web server running in
Puppy Linux Bionic32 or Bionic64. These steps will work in every Puppy from Lucid 5.2.8 upwards.

load devx for Bionic
load 32 bit compat lib if Bionic64
in a terminal :

Code: Select all

adduser www-data -D

these are the packages installed with the PPM

apache2_2.4.29
apache2-bin_2.4.29
apache2-data_2.4.29
apache2-utils_2.4.29
libaprutil1-dbd-sqlite3_1.6.1-2
libaprutil1-ldap_1.6.1-2
mime-support_3.60ubuntu1

Configuration files for apache2 are here: /etc/apache2
The configuration files for the apache2 server need to be sym-linked or modified
to run correctly. As one becomes more familiar with the system there are many tweaks.



I find that it is easier to use ROX and open /etc/apache2 and symlink manually the .ini files from
/etc/apache2/mods-available to /etc/apache2/mods-enabled and then sym-link the .conf files
from /etc/apache2/conf-available to /etc/apache2/sites-available

open /etc/apache2/apache2.conf and find : ServerRoot "/etc/apache2"
below it add : ServerName localhost
or which ever specific domain name is appropriate.

These are some of the controls:

Code: Select all

apache2ctl start|stop|restart

Using apache2ctl is the most reliable way of start|stop|restart|status the apache2 web server running in Bionic32 or Bionic64.

There are more which can be referenced in the Apache documentation. Apache runs well in Puppy Linux but needs systemd for using the service commands as in Ubuntu. So without tracking down the differences to get those to work, using apache2ctl is the reliable way to go.

the web server root is /var/www/html
start the web server :

Code: Select all

 apache2ctl start

open a browser and open http//localhost/

Next step is installing the PHP.

[mohittomar13]

Thanks for the post. Please also upload the steps for PHP and mySQL. I think that this post should be closed for new replies and must serve as a guide/manual rather than a Q/A post (Normal Forum Thread). Or a new Section must be created on the Forum which serves as the central place for comman puppy HowTo. I hope you understand what I mean. You may also delete this post of mine and tag your post at the top in the new Section (If you create a new Section). Thanks

[mohittomar13]

I followed your instructions and tried to restart the server after adding the required lines in the apache2.cfg. After running the command to restart the server this is what I got.

Code: Select all

root@puppyPC5832:~# apache2ctl restart
AH00534: apache2: Configuration error: No MPM loaded.
Action 'restart' failed.
The Apache error log may have more information.

[rockedge]

once we have a good set of instructions we can consider locking the topic but for now we will keep improving them here!

open /etc/apache2/mods-enabled and look for the sym-links /etc/apache2/mods-enabled/mpm_prefork.conf and /etc/apache2/mods-enabled/mpm_prefork.load that these 2 exist.

try in a terminal:

Code: Select all

a2enmod mpm_prefork

make sure there is only mpm_prefork. If there is a mpm_event.conf and / or mpm_event.load delete both.

There can only be one form of mpm enabled. There could be one of these three:
mpm_prefork (this is the one needed for php-cgi)
mpm_event
mpm_worker

more will be included on using php-fpm for multi-thread operation of PHP which will use one of the other mpm modules.

also possible to use in a terminal:

Code: Select all

a2dismod mpm_event
a2enmod mpm_prefork
apache2ctl restart

[mohittomar13]

Hi.. I found this link and XAMPP is working at 1000% speed

http://wikka.puppylinux.com/XAMPP

This serves my purpose.

For downloading the .sfs follow the link below.

https://code.google.com/archive/p/xampp-puppy/downloads

[rockedge]

Yes I used XAMPP a lot with Puppy Linux.

How To Build ZoneMinder 1.28.109 on an XAMPP stack

[CasparPup]

Hi.. I found this link and XAMPP is working at 1000% speed

http://wikka.puppylinux.com/XAMPP

This serves my purpose.

For downloading the .sfs follow the link below.

https://code.google.com/archive/p/xampp-puppy/downloads

This is a package from 2013. From my point of view it's too old.

[rockedge]

Might be the best bet to install Apache2, mariaDB (mysql) and PHP7 directly. This will be more like a setup one would encounter commercially.

[gabtech]

How do I enable apache to autostart at boot?

[rockedge]

you can do this by enabling the service. Method #1 is use the Puppy Setup and access the services and check the enable box. Usually is automatically done but double check it.

Method #2 on the command line (or something like this command)

Code: Select all

service apache2 enable

Screenshot(74).png (40.89 KiB) Viewed 3528 times

[gabtech]

@rockedge

Thanks for the above solution.

Another problem here - I'm trying to configure maridb but I get the error msg in the screenshot attached below.

[rockedge]

Have you initialized the mysql server and then ran /mysql_secure_installation?

The error indicates that either the directory /var/run/mysqld does not exist and/or the mysql server is not running (mysqld)

So try in a terminal

Code: Select all

mysqld &
or
mysqld -uroot &

and report what happens please.

[gabtech]

This is the error I'm getting.

[rockedge]

Syntax Error!
the command should be: (check the spelling)

Code: Select all

mysqld -u root &
or
mysqld -uroot &

If it complains about using the user "mysql", try to add one with:

Code: Select all

adduser mysql

if there is an error doing that we will need to do some extra steps.

So looking at the screenshot the last command was typed in wrong!

[gabtech]

@rockedge

HI and thanks. Still getting errors.

[rockedge]

did you initialize the mysql server?

Code: Select all

mysqld --initialize --user=root

Change the owner of /var/log/mysql so it matches the server user. But first do the above then set your root password for mysql

[gabtech]

@rockedge

Thanks man for the help. I now need to install zoneminder, is the inform you outlined here - http://oldforum.puppylinux.com/puppy/vi ... p?t=101999 workable in fossa.

[rockedge]

This script that will install ZM. Open it up and use the parts you need from the point you are now. Which I assume you have the web server and mysql server running with PHP 7.2+

Remove the fake "gz" from the filename and make executable to run it if you want to.

02-install-fossa-zm.sh.gz

(76.45 KiB) Downloaded 63 times

[gabtech]

@rockedge

Thanks for script.